|
Manufacturers of
Products for Increased
Productivity and Profits
 O.D.
Tube & Pipe Surfacer
Product Specifications
|
Motor Pulley
|
6" dia
x 31/4" face (2 deg. crown)
|
|
Capacity
|
4" to
16" diameter
|
|
Abrasive
Belt Sizes
|
2" 21/2",3"
wide x 72" long
|
|
Abrasive
Belt Speed
|
5,500 SFPM
|
|
Spindle Speed
|
3,600 RPM
|
|
Full Load
AMPS
|
10 AMPS
|
|
Floor Space
|
40"
x 72"
|
|
Shipping
Weight Lbs.
|
400
|
Contact Wheel
Dia.
|
Recommended Spindle
RPM Range
|
SFPM
|
|
6"
|
1,500-3,000
|
2,356- 4,712
|
|
8"
|
1,500-3,000
|
3,142- 6,283
|
|
10"
|
1,200-2,500
|
3,142- 6,545
|
|
12"
|
1,200-2,500
|
3,769- 7,854
|
|
6"
|
1,000-2,000
|
3,665- 7,330
|
|
6"
|
1,000-2,000
|
4,189- 8,378
|
CONTACT WHEEL
The proper
contact wheel is an important factor in any grinding application. It is
often necessary to do a certain amount of testing
tobefore determining which contact wheel is best suited for a particular
job. To provide a starting point, the following contact wheels are stocked
at the factory:
- 90 durometer,
rubber covered, serrated face for rapid stock removal
- 70 durometer,
rubber covered, serrated face for general purpose grinding
- 50 durometer,
rubber covered, serrated face for moderate stock removal and polishing
MODELS
All six models
are identical except for the width of the contact wheel tire and the size
of the motor. Each use a 72" long abrasive belt. The width of the
belt and the size of the motor are indicated by the model numbers as indicated
on the chart below:
- Model
|
- Belt Size
|
- H.P.
|
- TPS-1
|
- 2"
x 72"
|
- 2
|
- TPS-2
|
- 21/2"
x 72"
|
- 2
|
- TPS-3
|
- 3"
x 72"
|
- 2
|
- TPS-4
|
- 2"
x 72"
|
- 3
|
- TPS-5
|
- 21/2"
x 72"
|
- 3
|
- TPS-6
|
- 3"
x 72"
|
- 3
|
TABLE REQUIREMENTS
Screenpro
will custom design and build your main support table based on the length
of the longest tube or pipe that you refinish. Our standard table is 72"
wide x 40" deep and will handle objects up to 36" in length.
CARRIAGE REQUIREMENT
The product
carriage holds and rotates the pipe or tube to be finished and is custom-built
to the customer's specifications. We require that the customer provide
us with the length and diameter of tube or pipe they wish to refinish.
A sample is preferred.
ELECTRICAL
CONTROLS
Standard electrical
controls consist of a manual starter wired 230 or 460V, 3 phase, 60 HZ.
SPECIAL REQUIREMENTS
Prices do
not include costs to conform to any local or state requirements that exceed
the requirements generally accepted nationally.
CANCELLATION
There will
be a cancellation charge for orders canceled after work on order has begun.
The amount of the charge will be determined by the degree of completion
at the time of cancellation.
GUARANTEE
Machinery
manufactured by Screenpro is
guaranteed to be free of defective material or faulty workmanship for a
period of one (1) year from date of shipment. Electric motors, control
and other commercial parts are covered by separate warranties from their
respective manufacturers. In the event of defective material or faulty
workmanship, the defective part must be returned to Screenpro,
freight prepaid, where it will be repaired or replaced at the discretion
of Screenpro. Labor
charges for removal and replacement of the part are not included in the
guarantee. Screenpro assumes
no liability
for any injuries to persons, damage to property or delays in production.
On special
machinery, Screenpro
guarantees the machinery supplied for a specific application will produce
the results equal to or better than those produced on sample parts at the
time of the quotation.
Please
click below:
|